User Forum of Software BASEMENT

klaus

User

Registered: 2016-09-29

Posts: 3

output xdmf

Hello,

I'm working on Basement 3.0(only hydraulics). I export the results in xdmf file (bottom_elevation, water_depth, water_surface, flow_velocity and ns_hyd_discharge ). In paraview 5.7.0, I can see the results as Layout very well. The problem is that paraview can not export the complete results in a SpreadShetView (Attribute: Cell data). Only the results from bottom_elevation, water_depth, water_surface without flow_velocity and ns_hyd_discharge are correct. The simulate results with flow_velocity and ns_hyd_discharge are failed with the output messages:

ERROR: In C:\bbd\6519e7fe\build\superbuild\paraview\src\VTK\Common\DataModel\vtkTable.cxx, line 355
vtkTable (00000265CFFCFB30): Column "flow_velocity_0" must have 46372 rows, but has 15457.

ERROR: In C:\bbd\6519e7fe\build\superbuild\paraview\src\VTK\Common\DataModel\vtkTable.cxx, line 355
vtkTable (00000265CFFCFB30): Column "flow_velocity_1" must have 46372 rows, but has 15457.

ERROR: In C:\bbd\6519e7fe\build\superbuild\paraview\src\VTK\Common\DataModel\vtkTable.cxx, line 355
vtkTable (00000265CFFCFB30): Column "flow_velocity_2" must have 46372 rows, but has 15457.

ERROR: In C:\bbd\6519e7fe\build\superbuild\paraview\src\VTK\Common\DataModel\vtkTable.cxx, line 355
vtkTable (00000265CFFCFB30): Column "flow_velocity_Magnitude" must have 46372 rows, but has 15457.

Do you know why?

Thank you for your help
Klaus

Matthias Bürgler

Developer

From: Zürich

Registered: 2019-04-04

Posts: 150

Re: output xdmf

Hi Klaus
This error only seems to occur with Paraview Version 5.7.0. With the versions Paraview 5.4 or 5.6 it works fine. I suggest to use an older version until we fix this,
Best regards
Matthias

Matteo Facchini

Developer

From: Trento

Registered: 2014-09-05

Posts: 281

Re: output xdmf

Dear BASEMENT users and developers

I am here to report the following behavior with BASEMENT 3.0 xdmf results in ParaView 5.8:

ParaView 5.8 has 3 xdmf readers, with the first one (XDMF reader) I am able to open BASEMENT results, but the graphic of the softwer gets twisted. With the other two (Xdmf readerS and Xdmf readerT) ParaView loads the results but if I try to visualize them, it crashes.

I solved this by downgrading to ParaView 5.6 and selecting the first xdmf reader (XDMF reader) when prompted to.

I hope this could help some other users

Cheers

Matteo

Matthias Bürgler

Developer

From: Zürich

Registered: 2019-04-04

Posts: 150

Re: output xdmf

Hi Matteo

Thank you for the hint! This issue will be solved with the next release.

Best regards
Matthias

Matteo Facchini

Developer

From: Trento

Registered: 2014-09-05

Posts: 281

Re: output xdmf

Hi Matthias,

ParaView 5.6 is still working only withm the XDMF reader. Maybe updating ParaView is helping?

Might it be a problem with the paths as it is for QGIS?

Cheers,
Matteo